301 Thickness 0.3 Precision Stainless Steel Container.etc Tableware
| Series | Grade | Characteristic | main applications |
| Austenite | Basic | 304 | Widely used, with good performance in corrosion resistance, heat
resistance, formability and strength in low temperature. This
material have no heat treatment hardening phenomenon ,weak
,magnetism | Home appliances ,chemical industry, medical apparatus and
instruments , construction industry and decoration parts |
| Austenite | Basic | 304L | Advantageous performance in intergranular corrosion resistance
,better used for the part which is hardly heat treated after
welding | Oil industry ,chemical industry ,building material ,heat resistant
parts and hardly heat treated parts |
| Austenite | Basic | 304J1 | The performance in corrosion resistance and processability is
slightly lower than 304 | Cooking utensil and domestic appliances |
| Austenite | Nickel Saving | BNDDQ | Economical austenitic stainless steel | Containers and domestic appliances |
| Austenite | Nickel Saving | BN2 | Economical austenitic stainless steel | Containers and domestic appliances |
| Austenite | High tensile strength | 301 | The content of Cr and Ni is lower than 304,its strength and
hardness can be increased by cold rolling ,with certain magnetism | Trains ,aviation industry ,and springs |
| Austenite | High tensile strength | 301B |
| Austenite | High tensile strength | 301S |
| Austenite | High tensile strength | 301L | Improving the intergranular corrosion resistance performance by
decreasing the C content based on 301 ,and adding N element to
offset the impact of declined C content | Trains ,aviation industry ,and springs |
| Austenite | Deep Drawing | B304CQ | Adding appropriate Cu element based on 304 to improve formability
,which benefit deep drawing | Domestic appliances |
| Austenite | Deep Drawing | B304DDQ | Improving the formability by increasing Ni content and adding Cu
element based on 304 | Domestic appliances |
| Austenite | High corrosion resisting | SUS316L | Compared with SUS316,this material has better intergranular
corrosion resistance ,lower strength in high temperature ,and have
no magnetism | Chemical equipments that need better corrosion resistance and
processing propert, food equipments and infrastructures along the
coast ±0.45 |
1. Specifications about stainless steel coil/sheet
Commodity | 6mm thick NO.1 AISI 321 304 304l 316 316l stainless steel sheet | Width | 1000mm-2000mm or as customer's requires. | Thickness | cold rolled:0.3mm-3.0mm hot rolled:3.0mm-100mm | Length | 1000mm - 6000mm or as customer's request | Surface | No.1,2b,8k,2d,Ba,No.4,No.6,No.8, etc. | Edge | Mill Edge and Slit Edge | Meterial | 310S,310,309,309S,316,316L,316Ti,317,317L,321,
321H,347,347H,304,304L,302,301,201,202,403,405,409,409L,410,410S,420,430,631,904L,etc | Grade | 300 series | Standards | AISI ASTM JIS SUS and GB | Certifications | ISO 9001,SGS, | Applications | Kitchenware, utensils, tableware, household appliances,
construction decoration and daily product. | Packing | Seaworthy wooden pallet or according to client's requirement | MIQ | 1 ton or free samples |
|
|
|
2. Product characteristic
SS Plates, SS Coils, Stainless Steel Plates, SS Sheets, Stainless
Steel Hot Rolled Plates Hastelloy Alloy Sheets, Hastelloy Plates,
ASME SB575 Hastelloy Plate, Hastelloy Plate, Hastelloy Alloy Coils,
Hastelloy Plates, Hastelloy Circle, Hastelloy Rolled PlatesInconel
Plates, Inconel Circle, Inconel Alloy Coils, ASME SB 168 Plate, JIS
NCF Plate, Inconel Plates, Inconel Alloy Sheets, Inconel Hot Rolled
Plates Supplier in Visakhapatnum,Vizag, India.Hastelloy Cold Rolled
Plates, ASTM B575 Hastelloy Shim Sheets, Hastelloy Sheets,
Hastelloy Alloy Plate Exporter,
3. Chemical Composition about stainless steel coil/sheet
| Classification | Grade | Main Chemical Compositon |
| C | Si | Mn | P | S | Ni | Cr | other |
| AUSTENITE | 301 | 0.15 | 1.00 | 2.00 | 0.045 | 0.03 | 6.00-8.00 | 16.0-18.0 | |
| 301L | 0.03 | 1.00 | 2.00 | 0.045 | 0.03 | 6.00-8.00 | 16.0-18.0 | N≤0.20 |
| 304 | 0.08 | 1.00 | 2.00 | 0.045 | 0.03 | 8.00-10.5 | 18.00-20.00 | |
| 304L | 0.03 | 1.00 | 2.00 | 0.045 | 0.03 | 9.00-13.0 | 18.00-20.00 | |
| 316 | 0.08 | 1.00 | 2.00 | 0.045 | 0.03 | 10.0-14.0 | 16.00-18.00 | Mo 2.0-3.0 |
| 316L | 0.03 | 1.00 | 2.00 | 0.040 | 0.03 | 12.0-15.0 | 16.00-18.00 | Mo 2.0-3.0 |
| 321 | 0.08 | 1.00 | 2.00 | 0.045 | 0.03 | 9.0-13.0 | 17.00-19.00 | Ti5XC%↑ |
| FERRITE | 409L | 0.03 | 1.00 | 1.00 | 0.040 | 0.03 | — | 10.5-11.75 | Ti6xC% |
| 430 | 0.12 | 0.75 | 1.00 | 0.040 | 0.03 | — | 16.00-18.00 | |
| 436L | 0.03 | 1.00 | 1.00 | 0.040 | 0.03 | — | 16.00-19.00 | |
| 444 | 0.03 | 1.00 | 1.00 | 0.040 | 0.03 | — | 17.00-19.00 | Mo 0.75-1.5 |
| MARTENSITE | 420J2 | 0.26-0.40 | 1.00 | 1.00 | 0.040 | 0.03 | — | 12.00-14.00 | |
4. Available Size Range by Grade and Surface Finish(Unit:mm)
| No. | Width
Thickness | 300 Series | 400 Series |
| 2D | 2B | NO3 | NO4 | HL | BA | 2D | 2B | NO3 | NO4 | HL | BA |
| 1 | 0.3≤t≤0.5 | | | Consultative Range | | | | Consultative Range | |
| 2 | 0.5≤t≤0.7 | | | | | | | | | | | | |
| 3 | 0.7≤t≤0.9 | Available Range | Available Range |
| 4 | 0.9≤t≤1.1 |
| 5 | 1.1≤t≤1.3 |
| 6 | 1.3≤t≤1.7 |
| 7 | 1.7≤t≤2.0 |
| 8 | 2.0≤t≤3.0 | | | | | | | | | | | | |
5. Surface Finish and Application area
| Surface Finish | Characteristics and application |
| NO.1 | Hot-rolled surface,annealed and pickled,can be used as cold-rolling
material,industrial tanks and chemical devices. |
| NO.2D | Colled-rolled,annealed and pickled without skinpass,the dull
products can be used as automobile parts,building material and
pipes. |
| NO.2B | The suiface brightness and flatness of NO2B is better than
NO2D.Then through a special surface treatment to improve its
mechanical properties,No2B could nearly satisfy comprehensive uses. |
| NO.3 | Polished with abrasive belt of grit#100-#120,have better brightness
with discontinuous coarse stia,used as inner and external ornaments
for building,electrical applicances and kitchen utensils etc. |
| NO.4 | Polished with abrasive belt of grit #150-#180,have better
brightness with discontinuous coarse stria,but thinner than NO3,are
used as bathtub building's inner and external ornaments electrical
appliances,kitchen utendils and food processing equipment etc. |
| #320 | Polished with abrasive belt of grif #320,have better brightness
with discontionous coarse stria,thinner than NO4,are used for
bathtub,buildings inner and external ornaments,eletircal
appliances,kitchen utensiles,food processing equipment etc. |
| HL | Polished with abrasive belt of grit #150-#320 on the NO4 finish and
has continuous streaks,mainly used as building's
ornaments,elevators,door of building,frontal plate etc. |
| BA | Cold rolled,bright annealed and skin-passed,the product have
excellent brightness and good reflesivity like mirror,used for
eletircal appliances, mirror,kitchen apparatus,ornament materials
etc. |
| Emboss | Provided with irregularities on one side by cold rolling(both sides
can be embossed),mainly used us building's ornaments,elebators,door
of building,frontal plate etc. |
6. SIZE AND TOLERANCE
1) Tolerance on Thickness(mm):The thickness is measured at any
point located more than 25 mm from the edges in the case of mill
edges and at any point located more than 15 mm from the edges in
case of slit edges.
| No. | Thickness | Width |
W<1250 | 1250≤W<1600 |
| 1 | 0.2≤t<0.25 | ±0.03 | — |
| 2 | 0.25≤t<0.30 | ±0.04 | — |
| 3 | 0.30≤t<0.60 | ±0.05 | ±0.08 |
| 4 | 0.60≤t<0.80 | ±0.07 | ±0.09 |
| 5 | 0.80≤t<1.00 | ±0.09 | ±0.10 |
| 6 | 1.00≤t<1.25 | ±0.10 | ±0.12 |
| 7 | 1.25≤t<1.60 | ±0.12 | ±0.15 |
| 8 | 1.6≤t<2.00 | ±0.15 | ±0.17 |
| 9 | 2.00≤t<2.50 | ±0.17 | ±0.22 |
| 10 | 2.50≤t<3.15 | ±0.22 | ±0.25 |
| 11 | 3.15≤t<4.00 | ±0.25 | ±0.30 |
| 12 | 4.00≤t<5.00 | ±0.35 | ±0.40 |
| 13 | 5.00≤t＜6.00 | ±0.40 | ±0.45 |
| 14 | t=6.0 | ±0.50 | ±0.50 |
2) Tolerance on width (mm)
Width(650≤W<2400):0~+5
3) Tolerance on length(mm)
Length(1000≤L≤3500):0~+10
Length(1000≤L≤3500):0~+15
4) Tolerance on flatness
Width | Length | Flatness |
W≤1000 | L≤2000 | ≤15 |
| W≤1000 | L>2000 | ≤20 |
W>1000 | L≤2000 | ≤20 |
W>1000 | L>2000 | ≤20 |
The above allowable deviation can be customized according to the
customer's personalized requirements.
7. APPLICATION
| Austenite | High corrosion resisting | 316L |
8.PACKAGE AND SHIPMENT
Item/Mode of packing | | Simple packing | General packing | Special packing |
Unit weight(mt) | Plate | Normal:1.5-3.5 Maximum:5.0 |
Coil | Normal:4.0-7.0 Maximum:22.0 | Normal:4.0-7.0 Maximum:8.0 |
Dimension(mm) | Plate | Width *Length=(650-1320)*(1000-4000) |
Coil | Inner diameter:508(normal)or 610 |
Recommendations | Applicable to direct customers located close to hong-steel
(Jiangsu, Zhejiang and Shanghai ) | Applicable to most domestic customers | Applicable to exportation and to domestic customers with special
requirements |
Characteristics | Not applicable to long distance transportation, Avoid frequent
transportation, Do not expose to outdoor ,Do not lift with steel
cable directly ,Not appropriate to high quality product like BA,
Lower packing cost | Do not expose to outdoor ,Better protection for products ,Lower
requirement for loading ,Unloading and transportation .Appropriate
to all types of surface finish product ,Lower packing cost | Better protection for products ,Lower requirement for loading
,Unloading and transportation ,Appropriate to all types of surface
finish product ,Higher packing cost ,Difficult to pack and low
efficiency |
1. What is the application about your Products?
A7. 1. Elevator door/cabin or and escalator’s side-wall.
2. Wall cladding inside or outside meeting room/ restaurant.
3. Facade when cladding over something, like columns in the lobby.
4. Ceiling in the supermarket. 5. Decorative draws in some
entertainment places.
2. How long Can You Guarantee for This Product/ Finish?
A8. Color guarantee for more than 10 years. Original materials
quality certificate can be provided.
3. Can we provide the photos or ideas to you, then you design for
us?
A9. Yes, we have the professional designer who can custom for you.
We will custom according to your information, then provide you the
CAD file before production.
4. Can we check with our goods before delivery?
A10. Yes, sure. Once we have finished the production, we will
information you, then ask you to check with your goods before
delivery.
